Home > Protocol Driver > Protocol Driver Error Access Gateway

Protocol Driver Error Access Gateway


For example: Save the web.config file and restart the Advanced Access Control services using the service configuration. Server general When you connect to your published application using the Program Neighbourhood till shows ‘protocol driver error’, it must be the load balancer or one of your XenApp servers. Several functions may not work. Or sometimes a reinstall is faster than troubleshooting. 3 – Transport problems At one of the faulty clients; check the IP configuration; check network card physically, cable, link LED, follow the have a peek at this web-site

But it comes down to this: the client cannot find the server. Ensure to use the latest IP stack for the client operating system. ------------------------------------------------------------- If all appropriate updates to the server and client are applied, attempt the following items: a. Socket operation on non-socket"Other users were getting the protocol driver error message, and again I was seeing the same error messages in the CAG Debug log. 1357-298915-1608712 Back to top Lurse All Rights Reserved.

Cannot Connect To The Citrix Xenapp Server.protocol Driver Error Windows 7

Thanks very much.Lenovo - ThinkPad 14" Laptop - 4GB Memory - 128GB Solid State Drive - BlackLenovo - IdeaPad Ultrabook 13.3" Touch-Screen Laptop - 4GB Memory - 500GB Hard Drive - After 5 days of being up, I started to receive the errors again. As soon as it fails over the error goes away and users are able to launch applications.201112161030.22 642823220 ns | :SERVER_DEBUG (073):SERVER_MISC_DEBUG (12) | failed at gethostbyname [stahost1.domain.com:0]: No Error. -

The Logon User Inte... ► 06/26 - 07/03 (6) Video Bar Loading... Do you see any errors? 1411-366174-1879714 Back to top Laban Milyard Members #4 Laban Milyard 6 posts Posted 18 June 2015 - 12:55 PM Duplicate Post.... 1411-366174-1879719 Back to top Laban I updated the client on one of my workstations to Receiver 3.1, and received a different error this morning. "Unable to launch your application. Xendesktop 7 Protocol Driver Error Note: Each idle winstation takes one megabte of RAM.

Check firewall rules also as my current set up is not complex.Basically added extra ports to the ICA Access Control of List on the new CAG.while on the old CAG2000 model Xendesktop 7.6 Protocol Driver Error Ensure that the Network Interface Card (NIC) has the latest driver installed. 3. René is CCNP , Aruba Certified Mobility Expert (ACMX #438), Aruba Certified ClearPass Professional (ACCP), FCNSP and Certified Ethical Hacker (CEF) certified. http://discussions.citrix.com/topic/298915-protocol-driver-error/ Using Storefront on the XenApp server.

If users are receiving this error when attempting to authenticate to a Server Farm, make sure that the Program Neighborhood Service is started. Citrix Protocol Driver Error Web Interface Screenshot attached. Contact your helpdesk with the following information: Cannot connect to the Citrix Xenapp server. See the following articles for causes this can occur and procedures to troubleshoot the error: CTX108782 – Error: Cannot connect to the Citrix MetaFrame server.

  • Error: 1030 - Protocol Driver Error Troubleshooting Steps and Suggestions • CTX911130 • Created On: Feb 04, 2003 • Updated On: Jul 09, 2014 • Article • Topic: Connectivity Symptoms A
  • For each server involved you should check: ccan you ping the server check the load balancing, on a XenApp server: qfarm /load is the IMA service running is the logon service
  • My network colleauge didn't open session reliability port (2598) from netscalers MIP and NSIP to internal Citrix terminal farm...
  • As soon as I rebooted the primary CAG, I was able to launch applications without error. 1357-298915-1611733 Back to top Kevin Pasko Members #10 Kevin Pasko 23 posts Posted 23 March
  • I know enough about ...
  • It will either be SSLProxyHost or it will be a XenApp or VDA IP address. 1411-366174-1879739 Back to top Laban Milyard Members #8 Laban Milyard 6 posts Posted 18 June 2015
  • If using Network Address Translation, refer to CTX039746 – IMA and ICA Browsing With Firewall Address Translation (NAT).

Xendesktop 7.6 Protocol Driver Error

Please re-enable javascript to access full functionality. their explanation Please re-enable javascript to access full functionality. Cannot Connect To The Citrix Xenapp Server.protocol Driver Error Windows 7 After running for around 10 days, the CAG starts refusing connections with "Protocol driver error" as the reason. Citrix Xendesktop Protocol Driver Error Problem was in internal firewall.

Sebastian: got the problem solved, pre created the cno first ... Check This Out b. Now I have to wait and see if this actually solved the problem, but I guess it has. StoreFront is using a self signed certificate. Ctx134276

If they are not activated, you receive the 1030 error. Troubleshooting ‘Protocol drive error’ can have so many causes, and here’s a list of things you should check. 1 - Step one is to determine what the problem is, we split On the Citrix StoreFront Server (Server 2008 R2), in RemoteApp Manager, the Digital Signature Setting did not have a certificate assigned. http://caribtechsxm.com/protocol-driver/protocol-driver-error-access-gateway-5.php Protocol Driver error"http://terenceluk.blogspot.com/2012/04/launching-xendesktop-55-or-56-desktop.html … then one of the other items to check is to ensure that your NetScaler Access Gateway actually has a static route to your virtual desktop's subnet (assuming

Applications are being launched from the Program Neighborhood Content Delivery Agent (CDA). The Connection To Failed With Status (protocol Driver Error) Also, be sure that your Windows 2000 Terminal Licenses are activated! If this is not successful, follow the instructions previously noted.

Create a Custom ICA Connection to the published application and attempt the connection.

Example of an Access Gateway log showing failure: This line shows a request to nfuselaunch at 13:11:48: (08/31/06 13:11:48): 2:server:aacd:: request: This line shows a failed STA ticket check at And, since I have latest Storefront (2.6.0) I'm using same FQDN for external aswell... Check the event log for any 1004 Terminal Server licensing errors. 5. Protocol Driver Error Wyse But later during the day we realised that there was a DNS failure in our environment and my NetScalers were pointed to the failed DNS server.

Error: "1030 - Protocol Driver Error" Troubleshoot... I tried adding the STA port to the session reliability ICA access control list, but that did not make a difference either. Troubleshooting and Explaining the Citrix Universa... have a peek here Any help would be much appreciated.