Home > Protocol Error > Protocol Error Between Bss And Msc

Protocol Error Between Bss And Msc

Published in: Mobile 0 Comments 1 Like Statistics Notes Full Name Comment goes here. 12 hours ago Delete Reply Spam Block Are you sure you want to Yes No Your message All rights reserved. H323 SIP softswitch >> Site highlights Home page Online Calculators Products Excel call center VoIP services Technical papers What is an Erlang? Page16Copyright © 2008 Huawei Technologies Co., Ltd. http://caribtechsxm.com/protocol-error/protocol-error-17.php

All rights reserved. If you continue browsing the site, you agree to the use of cookies on this website. All rights reserved. Page30Copyright © 2008 Huawei Technologies Co., Ltd. http://dualsoftswitch.com/forum/erlang/thread.htx?thread=4895

COMPLETE LAYER 3 INFORMATION Information Element type Direction Description Message Type M BSC- >MSC Cell Identifier M BSC- >MSC Layer 3 Information M BSC- >MSC “paging response” etc. Page6Copyright © 2008 Huawei Technologies Co., Ltd. Contact us VoIP calling Premium quality termination for wholesale carriers with their own VoIP switch. 44Direct >> Our lowest rates for wholesale carriers with their own VoIP switch. 44Mobile >> Our

  • Bits 7-1 indicate the permitted speech version identifier; 765 4321 000 0001GSM speech full rate version 1 001 0001GSM speech full rate version 2 010 0001GSM speech full rate version 3
  • URD - 2nd December 2011 (06:19 GMT)we get lot of call drops because of Radio Interface Messafe failuers.
  • Name Enter your name.
  • Page2Copyright © 2008 Huawei Technologies Co., Ltd.
  • Page7Copyright © 2008 Huawei Technologies Co., Ltd.
  • Ericson claims that 2nd assignment request is according to 3GPP and MSC can decide for a new TCH, I went through 3GPP Doc and honestly i couldnt understand it fully.
  • BSSAP Main Procedure Analysis 2.1 Paging 2.2 Initial MS Message 2.3 Cipher Mode Control 2.4 Assignment 2.5 Handover 2.6 Release 2.7 DTAP Message Contents 62.
  • Resource Indication The purpose of the Resource Indication procedure is to inform the MSC of the following information: The amount of radio resource that is spare at the BSS and available
  • A RESET message is received.

Page70Copyright © 2008 Huawei Technologies Co., Ltd. Flow Control The flow control is adopted to prevent entities from entering unstable state due to overload. All rights reserved. 2. All rights reserved.

Cipher Mode Control Procedure  The cipher mode control procedure allows the MSC to pass cipher mode information to the BSS to select and load the user data and signalling encryption All rights reserved. Cipher Mode Control The Cipher Mode Control procedure allows the MSC to pass cipher mode control information to the BSS to select and load the user device and signaling encryption device http://www.slideshare.net/kendallle5/owa330011-bssap-protocol-analysis-issue-10 Requests for documents are now being removed from this forum.

Reset The purpose of the Reset procedure is to initialize the BSS or MSC in the event of a failure. Bill My Calls >> Protocol error between MSC and BSC Erlang for Excel An Add-In for Microsoft Excel that lets you use Erlang B and C functions in your own Excel Four products in one, plus Erlang for Excel free. This cannot easily be derived from the traffic that the MSC is carrying.

Notes: (duxiaoqin 20070925) BSSMAP Procedures BSSMAP protocol mainly implements the following functional procedures: Assignment The purpose of the Assignment procedure is to ensure that the correct dedicated radio resource can be Not included means that there is no potential current LSA in the target cell. Clipping is a handy way to collect important slides you want to go back to later. Then, the BSS marks any assigned terrestrial circuit as idle and returns a CLEAR COMPLETE message to the MSC.

Let's focus on "routing" .. Check This Out any explanations about this problem and possible solutions? Cipher Mode Control The Cipher Mode Control procedure allows the MSC to pass cipher mode control information to the BSS to select and load the user device and signaling encryption device DTAP BSSMS L3 Message: CALL CONFIRM MSC L3 message: SETUP DTAP: CALL CONFIRMATION DTAP: SETUP 70.

Group Call Reference This element is included if the MS is in a voice broadcast or voice group call. Handover from A cell to B cell that located in different BSC (Same MSC) cannot be performed. The ultimate in Erlang traffic modelling flexibility and data sharing. Source Queuing Indication The purpose of the Queuing Indication procedure is to inform the MSC of a delay in the allocation of the necessary dedicated radio resources by the BSS.

The transaction ends, for example, call clearing. During handover execution, the dedicated radio resources will not be released and the terrestrial resources will not be marked as idle until a CLEAR COMMAND message is received from the MSC Declaring LACs and installing patch, Inter_MSC_HO_Incoming_Failure is solved in our case we had.

Page3Copyright © 2008 Huawei Technologies Co., Ltd.

A cell change is required at call setup due to congestion, for example, directed retry. VoIP Calculator Our entry level VoIP calculator allowing you to easily calculate your Voice over IP bandwidth requirements. In case of a failure at a part of the MSC or BSS, the Clearing procedure can be used to erase the affected parts. All rights reserved.

And Yes, timer T8=14s in our network. Page15Copyright © 2008 Huawei Technologies Co., Ltd. Contact us VoIP calling Premium quality termination for wholesale carriers with their own VoIP switch. 44Direct >> Our lowest rates for wholesale carriers with their own VoIP switch. 44Mobile >> Our have a peek here On receipt of CLEAR COMPLETE, the MSC releases any assigned terrestrial resources at the local end.

Generated Mon, 24 Oct 2016 20:12:57 GMT by s_wx1126 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection